Pure Sine wave inverter with Built in Charger with LCD- 10KW
Provide Pure Sine Wave power for all your alternative energy needs with the Magnizon POWER MPS-10K48-LCD. This inverter/charger supplies 10KW watts of continuous 230V /50Hz AC power. Reliable large transformer design and frequency control powers very much compatible to all varieties of loads.

Features

  • 48V DC or 230V AC input; 230V, 50 Hz output (hardwired)
  • 10KW continuous output, 30000 watts peak output
  • Microprocessor controlled Smart UPS & Solar operational mode
  • 4-Step Progressive Charging & 7-Battery Type Selector
  • Fully compatible for Solar/Wind solutions for Hybrid configuration
  • Pure sine wave output with LCD display
  • High Efficiency Using Line-Interactive Circuit Topology(Full Bridge Topology)
  • Quiet, high efficiency operation, high surge capacity and low idle current
  • CE Safety
  • Provides safe and reliable power protect for the following equipment - Equipment is Office and Public Home Appliances, IT Network Equipment, Manufacture Control System, Solar Energy System Oil field and Fieldwork
  • On inverter: High overload ability, Low battery voltage trip selectable, extracting max power from various batteries with different protections, Low quiescent current, selectable sensing cycle to reduce power consumption
  • On battery charger: 3-step intelligent battery charging , 8 preset battery type selector plus de-sulphation for totally flat batteries ,Powerful charge rate up to 100Amp ,selectable charging current ,PFC(Power Factor Correction) for charger, less power consumption than conventional units
  • On Transfer: Delay before transfer, extra protections for loads under generator mode , Input AC voltage range selectable, for different kinds of loads ,8 ms typical transfer time, guarantees power continuity ,30A/40A through current ability ,Output voltage regulation optional
  • On remote control & other features Ability to switch the unit on/off , Ability to select/deselect power saver mode ,17 alarms/warnings, informative for easier operation and trouble-shooting ,LCD status display available ,RS232 communication port optional

Applications

  • Well designed for hybrid applications where solar/wind energy systems connected along with grid or generator sets without using any relay and control mechanism
  • Versatile inverter/charger with pure sine wave system with seamless transfer switching serves as an automotive inverter for RVs, trucks, standalone alternative power source with high end back up times with various battery technologies(VRLA, GEL, Deep cycle, Ni-Cd and many more)
  • Off-grid and On-grid applications
  • Telecom and ATM applications
  • Remote closets and small computer room applications.

Model No

MPS-10K48SW-LCD

Nominal Power

10000Watts

Input Specification

Input Phase & Wave Form

Single Phase & Sine wave (Utility or Generator)

Nominal Voltage

220/230/240V AC

Input AC voltage Window

154-273C AC

Line Low Transfer

154V +/- 4%

Low Voltage Re engage

164V +/- 4%

High Voltage Trip

273V +/- 4%

High Voltage Re engage

263V +/- 4%

Max Input AC Voltage

270V

Nominal Input Frequency

50Hz or 60Hz (Auto detect)

Low frequency trip

40Hz

High frequency trip

80Hz

Output Connection type

Hardwire via built in junction box with cover plate

Inverter Output Specification

Output Wave form & Phase

Pure Sine wave & Single Phase (Bypass mode sync to Input)

Power Factor

1

Nominal Output Voltage RMS

220/230/240V AC (L-N) (same as input on Bypass mode)

Output Voltage regulation

+/-10% rms (bypass mode sync to input)

Output frequency

50Hz +/-0.3Hz or 60Hz+/-0.3Hz

Nominal Efficiency

>88%

Output Connection type

Hardwire via built in junction box with cover plate

Surge rating/crest factor

3 times of rating

Output continuous power in Watts

10000

Output continuous power in VA

10000

Short circuit protection

Yes, fault after 10sec

DC Input Specification

Nominal Input Voltage Dc

48V DC

Minimum start voltage Dc

40V DC

Low battery Alarm

44V DC

Low battery trip

40V DC

High Voltage alarm

64V DC

Over Charge Voltage

62.8V DC

Max Charging Current

85A DC

DC Connection type

DC INPUT: Set of 2 DC bolt-down terminals. AC INPUT: Hardwire via built in junction box with cover plate

Transfer Efficiency

Transfer Time

6-10mSec

Line Mode

>95%

Battery Model

>85%

Power Save

Available when the load is less than 75W

Indicators/Alarms

4-LED Status Display

Charge, Line, Inverter & fault

LCD Display

Input Voltage, Output Voltage, Frequency, Battery voltage, Load, Temperature, Charge current & Fault

Switch Selector

Saving Mode is On/Off when push the switch forward/backwards, keeping it horizontal is turning the inverter Off

Audible Alarm

Sounding when the heat-sink's temperature is over 105deg C and shutdown after 30 seconds

Protections

Low Battery, Over charging, Over temp & over load

Communications

RJ11/RS232 (optional)

Environmental Details

Operating Temp

0-40deg C

Humidity

0-95% RH (non-condensing)

Audible Noise

<60dB

Physical Details

Size (in mm)

584x450x202

Weight

64Kgs

Warranty

2 Year limited warranty Extendable up to 4 years

Safety

EMC/CE/ROHS/ISO9001

ISO 9001:2005

ISO 14000:2005

RoHs